FW: HELP!!! HELP!!! HELP!!!

["Matthew K. Lee" <mattl () rycan com>]

-----Original Message-----
From: Matthew K. Lee 
Sent: Friday, November 12, 2004 8:53 AM
To: 'Jeremiah J Batac'
Subject: RE: [Snort-users] HELP!!! HELP!!! HELP!!!
 
What happens when you comment out the following lines:
 
preprocessor http_inspect: global \
    iis_unicode_map unicode.map 287
preprocessor http_inspect_server: server default \
    profile all ports { 80 8080 8180 } oversize_dir_length 500
Thanks,
 
Matt.
 
-----Original Message-----
From: Jeremiah J Batac [mailto:jjbatac () yahoo com] 
Sent: Friday, November 12, 2004 8:50 AM
To: Matthew K. Lee
Subject: RE: [Snort-users] HELP!!! HELP!!! HELP!!!
 
Matt,
 
Here is my snort.conf
 
#--------------------------------------------------
#   http://www.snort.org     Snort 2.1.0 Ruleset
#     Contact: snort-sigs () lists sourceforge net
#--------------------------------------------------
# $Id: snort.conf,v 1.142.2.2 2004/08/05 18:55:37 jhewlett Exp $
#
###################################################
# This file contains a sample snort configuration. 
# You can take the following steps to create your own custom
configuration:
#
#  1) Set the network variables for your network
#  2) Configure preprocessors
#  3) Configure output plugins
#  4) Customize your rule set
#
###################################################
# Step #1: Set the network variables:
#
# You must change the following variables to reflect your local network.
The
# variable is currently setup for an RFC 1918 address space.
#
# You can specify it explicitly as: 
#
# var HOME_NET 192.168.2.0/27
#
# or use global variable $<interfacename>_ADDRESS which will be always
# initialized to IP address and netmask of the network interface which
you run
# snort at.  Under Windows, this must be specified as
# $(<interfacename>_ADDRESS), such as:
# $(\Device\Packet_{12345678-90AB-CDEF-1234567890AB}_ADDRESS)
#
# var HOME_NET $eth0_ADDRESS
#
# You can specify lists of IP addresses for HOME_NET
# by separating the IPs with commas like this:
#
# var HOME_NET [192.168.2.0/27]
#
# MAKE SURE YOU DON'T PLACE ANY SPACES IN YOUR LIST!
#
# or you can specify the variable to be any IP address
# like this:
var HOME_NET any
# Set up the external network addresses as well.  A good start may be
"any"
var EXTERNAL_NET any
# Configure your server lists.  This allows snort to only look for
attacks to
# systems that have a service up.  Why look for HTTP attacks if you are
not
# running a web server?  This allows quick filtering based on IP
addresses
# These configurations MUST follow the same configuration scheme as
defined
# above for $HOME_NET.  
# List of DNS servers on your network 
var DNS_SERVERS $HOME_NET
# List of SMTP servers on your network
var SMTP_SERVERS $HOME_NET
# List of web servers on your network
var HTTP_SERVERS $HOME_NET
# List of sql servers on your network 
var SQL_SERVERS $HOME_NET
# List of telnet servers on your network
var TELNET_SERVERS $HOME_NET
# List of snmp servers on your network
var SNMP_SERVERS $HOME_NET
# Configure your service ports.  This allows snort to look for attacks
destined
# to a specific application only on the ports that application runs on.
For
# example, if you run a web server on port 8081, set your HTTP_PORTS
variable
# like this:
#
# var HTTP_PORTS 8081
#
# Port lists must either be continuous [eg 80:8080], or a single port
[eg 80].
# We will adding support for a real list of ports in the future.
# Ports you run web servers on
#
# Please note:  [80,8080] does not work.
# If you wish to define multiple HTTP ports,
# 
## var HTTP_PORTS 80 
## include somefile.rules 
## var HTTP_PORTS 8080
## include somefile.rules 
var HTTP_PORTS 80
# Ports you want to look for SHELLCODE on.
var SHELLCODE_PORTS !80
# Ports you do oracle attacks on
var ORACLE_PORTS 1521
# other variables
# 
# AIM servers.  AOL has a habit of adding new AIM servers, so instead of
# modifying the signatures when they do, we add them to this list of
servers.
var AIM_SERVERS
[64.12.24.0/24,64.12.25.0/24,64.12.26.14/24,64.12.28.0/24,64.12.29.0/24,
64.12.161.0/24,64.12.163.0/24,205.188.5.0/24,205.188.9.0/24]
# Path to your rules files (this can be a relative path)
# Note for Windows users:  You are advised to make this an absolute
path,
# such as:  c:\snort\rules
var RULE_PATH ../rules
# Configure the snort decoder
# ============================
#
# Snort's decoder will alert on lots of things such as header
# truncation or options of unusual length or infrequently used tcp
options
#
#
# Stop generic decode events:
#
# config disable_decode_alerts
#
# Stop Alerts on experimental TCP options
#
# config disable_tcpopt_experimental_alerts
#
# Stop Alerts on obsolete TCP options
#
# config disable_tcpopt_obsolete_alerts
#
# Stop Alerts on T/TCP alerts
#
# In snort 2.0.1 and above, this only alerts when a TCP option is
detected
# that shows T/TCP being actively used on the network.  If this is
normal
# behavior for your network, disable the next option.
#
# config disable_tcpopt_ttcp_alerts
#
# Stop Alerts on all other TCPOption type events:
#
# config disable_tcpopt_alerts
#
# Stop Alerts on invalid ip options
#
# config disable_ipopt_alerts
# Configure the detection engine
# ===============================
#
# Use a different pattern matcher in case you have a machine with very
limited
# resources:
#
# config detection: search-method lowmem
###################################################
# Step #2: Configure preprocessors
#
# General configuration for preprocessors is of 
# the form
# preprocessor <name_of_processor>: <configuration_options>
# Configure Flow tracking module
# -------------------------------
#
# The Flow tracking module is meant to start unifying the state keeping
# mechanisms of snort into a single place. Right now, only a portscan
detector
# is implemented but in the long term,  many of the stateful subsystems
of
# snort will be migrated over to becoming flow plugins. This must be
enabled
# for flow-portscan to work correctly.
#
# See README.flow for additional information
#
preprocessor flow: stats_interval 0 hash 2
# frag2: IP defragmentation support
# -------------------------------
# This preprocessor performs IP defragmentation.  This plugin will also
detect
# people launching fragmentation attacks (usually DoS) against hosts.
No
# arguments loads the default configuration of the preprocessor, which
is a 60
# second timeout and a 4MB fragment buffer. 
# The following (comma delimited) options are available for frag2
#    timeout [seconds] - sets the number of [seconds] that an unfinished

#                        fragment will be kept around waiting for
completion,
#                        if this time expires the fragment will be
flushed
#    memcap [bytes] - limit frag2 memory usage to [number] bytes
#                      (default:  4194304)
#
#    min_ttl [number] - minimum ttl to accept
# 
#    ttl_limit [number] - difference of ttl to accept without alerting
#                         will cause false positves with router flap
# 
# Frag2 uses Generator ID 113 and uses the following SIDS 
# for that GID:
#  SID     Event description
# -----   -------------------
#   1       Oversized fragment (reassembled frag > 64k bytes)
#   2       Teardrop-type attack
preprocessor frag2
# stream4: stateful inspection/stream reassembly for Snort
#----------------------------------------------------------------------
# Use in concert with the -z [all|est] command line switch to defeat
stick/snot
# against TCP rules.  Also performs full TCP stream reassembly, stateful
# inspection of TCP streams, etc.  Can statefully detect various
portscan
# types, fingerprinting, ECN, etc.
# stateful inspection directive
# no arguments loads the defaults (timeout 30, memcap 8388608)
# options (options are comma delimited):
#   detect_scans - stream4 will detect stealth portscans and generate
alerts
#                  when it sees them when this option is set
#   detect_state_problems - detect TCP state problems, this tends to be
very
#                           noisy because there are a lot of crappy ip
stack
#                           implementations out there
#
#   disable_evasion_alerts - turn off the possibly noisy mitigation of
#                            overlapping sequences.
#
#
#   min_ttl [number]       - set a minium ttl that snort will accept to
#                            stream reassembly
#
#   ttl_limit [number]     - differential of the initial ttl on a
session versus
#                             the normal that someone may be playing
games.
#                             Routing flap may cause lots of false
positives.
# 
#   keepstats [machine|binary] - keep session statistics, add "machine"
to 
#                         get them in a flat format for machine reading,
add
#                         "binary" to get them in a unified binary
output 
#                         format
#   noinspect - turn off stateful inspection only
#   timeout [number] - set the session timeout counter to [number]
seconds,
#                      default is 30 seconds
#   memcap [number] - limit stream4 memory usage to [number] bytes
#   log_flushed_streams - if an event is detected on a stream this
option will
#                         cause all packets that are stored in the
stream4
#                         packet buffers to be flushed to disk.  This
only 
#                         works when logging in pcap mode!
#
# Stream4 uses Generator ID 111 and uses the following SIDS 
# for that GID:
#  SID     Event description
# -----   -------------------
#   1       Stealth activity
#   2       Evasive RST packet
#   3       Evasive TCP packet retransmission
#   4       TCP Window violation
#   5       Data on SYN packet
#   6       Stealth scan: full XMAS
#   7       Stealth scan: SYN-ACK-PSH-URG
#   8       Stealth scan: FIN scan
#   9       Stealth scan: NULL scan
#   10      Stealth scan: NMAP XMAS scan
#   11      Stealth scan: Vecna scan
#   12      Stealth scan: NMAP fingerprint scan stateful detect
#   13      Stealth scan: SYN-FIN scan
#   14      TCP forward overlap
preprocessor stream4: disable_evasion_alerts
# tcp stream reassembly directive
# no arguments loads the default configuration 
#   Only reassemble the client,
#   Only reassemble the default list of ports (See below),  
#   Give alerts for "bad" streams
#
# Available options (comma delimited):
#   clientonly - reassemble traffic for the client side of a connection
only
#   serveronly - reassemble traffic for the server side of a connection
only
#   both - reassemble both sides of a session
#   noalerts - turn off alerts from the stream reassembly stage of
stream4
#   ports [list] - use the space separated list of ports in [list],
"all" 
#                  will turn on reassembly for all ports, "default" will
turn
#                  on reassembly for ports 21, 23, 25, 53, 80, 143, 110,
111
#                  and 513
preprocessor stream4_reassemble
# http_inspect: normalize and detect HTTP traffic and protocol anomalies
#
# lots of options available here. See doc/README.http_inspect.
# unicode.map should be wherever your snort.conf lives, or given
# a full path to where snort can find it.
preprocessor http_inspect: global \
    iis_unicode_map unicode.map 287
preprocessor http_inspect_server: server default \
    profile all ports { 80 8080 8180 } oversize_dir_length 500
#
#  Example unqiue server configuration
#
#preprocessor http_inspect_server: server 1.1.1.1 \
#    ports { 80 3128 8080 } \
#    flow_depth 0 \
#    ascii no \
#    double_decode yes \
#    non_rfc_char { 0x00 } \
#    chunk_length 500000 \
#    non_strict \
#    oversize_dir_length 300 \
#    no_alerts

# rpc_decode: normalize RPC traffic
# ---------------------------------
# RPC may be sent in alternate encodings besides the usual 4-byte
encoding
# that is used by default. This plugin takes the port numbers that RPC
# services are running on as arguments - it is assumed that the given
ports
# are actually running this type of service. If not, change the ports or
turn
# it off.
# The RPC decode preprocessor uses generator ID 106
#
# arguments: space separated list
# alert_fragments - alert on any rpc fragmented TCP data
# no_alert_multiple_requests - don't alert when >1 rpc query is in a
packet
# no_alert_large_fragments - don't alert when the fragmented
#                            sizes exceed the current packet size
# no_alert_incomplete - don't alert when a single segment
#                       exceeds the current packet size
preprocessor rpc_decode: 111 32771
# bo: Back Orifice detector
# -------------------------
# Detects Back Orifice traffic on the network.  Takes no arguments in
2.0.
# 
# The Back Orifice detector uses Generator ID 105 and uses the 
# following SIDS for that GID:
#  SID     Event description
# -----   -------------------
#   1       Back Orifice traffic detected
preprocessor bo
# telnet_decode: Telnet negotiation string normalizer
# ---------------------------------------------------
# This preprocessor "normalizes" telnet negotiation strings from telnet
and ftp
# traffic.  It works in much the same way as the http_decode
preprocessor,
# searching for traffic that breaks up the normal data stream of a
protocol and
# replacing it with a normalized representation of that traffic so that
the
# "content" pattern matching keyword can work without requiring
modifications.
# This preprocessor requires no arguments.
# Portscan uses Generator ID 109 and does not generate any SID
currently.
preprocessor telnet_decode
# Flow-Portscan: detect a variety of portscans
# ---------------------------------------
# Note:  The Flow preprocessor (above) must first be enabled for
Flow-Portscan to
# work.
#
# This module detects portscans based off of flow creation in the flow
# preprocessors.  The goal is to catch one->many hosts and one->many
# ports scans.
#
# Flow-Portscan has numerous options available, please read
# README.flow-portscan for help configuring this option. 
# Flow-Portscan uses Generator ID 121 and uses the following SIDS for
that GID:
#  SID     Event description
# -----   -------------------
#   1       flow-portscan: Fixed Scale Scanner Limit Exceeded
#   2       flow-portscan: Sliding Scale Scanner Limit Exceeded 
#   3       flow-portscan: Fixed Scale Talker Limit Exceeded
#   4     flow-portscan: Sliding Scale Talker Limit Exceeded
# preprocessor flow-portscan: \
# talker-sliding-scale-factor 0.50 \
# talker-fixed-threshold 30 \
# talker-sliding-threshold 30 \
# talker-sliding-window 20 \
# talker-fixed-window 30 \
# scoreboard-rows-talker 30000 \
# server-watchnet [10.2.0.0/30] \
# server-ignore-limit 200 \
# server-rows 65535 \
# server-learning-time 14400 \
# server-scanner-limit 4 \
# scanner-sliding-window 20 \
# scanner-sliding-scale-factor 0.50 \
# scanner-fixed-threshold 15 \
# scanner-sliding-threshold 40 \
# scanner-fixed-window 15 \
# scoreboard-rows-scanner 30000 \
# src-ignore-net [192.168.1.1/32,192.168.0.0/24] \
# dst-ignore-net [10.0.0.0/30] \
# alert-mode once \
# output-mode msg \
# tcp-penalties on
# arpspoof
#----------------------------------------
# Experimental ARP detection code from Jeff Nathan, detects ARP attacks,
# unicast ARP requests, and specific ARP mapping monitoring.  To make
use of
# this preprocessor you must specify the IP and hardware address of
hosts on
# the same layer 2 segment as you.  Specify one host IP MAC combo per
line.
# Also takes a "-unicast" option to turn on unicast ARP request
detection. 
# Arpspoof uses Generator ID 112 and uses the following SIDS for that
GID:
#  SID     Event description
# -----   -------------------
#   1       Unicast ARP request
#   2       Etherframe ARP mismatch (src)
#   3       Etherframe ARP mismatch (dst)
#   4       ARP cache overwrite attack
#preprocessor arpspoof
#preprocessor arpspoof_detect_host: 192.168.40.1 f0:0f:00:f0:0f:00

# Performance Statistics
# ----------------------
# Documentation for this is provided in the Snort Manual.  You should
read it.
# It is included in the release distribution as doc/snort_manual.pdf
# 
# preprocessor perfmonitor: time 300 file /var/snort/snort.stats pktcnt
10000
####################################################################
# Step #3: Configure output plugins
#
# Uncomment and configure the output plugins you decide to use.  General
# configuration for output plugins is of the form:
#
# output <name_of_plugin>: <configuration_options>
#
# alert_syslog: log alerts to syslog
# ----------------------------------
# Use one or more syslog facilities as arguments.  Win32 can also
optionally
# specify a particular hostname/port.  Under Win32, the default hostname
is
# '127.0.0.1', and the default port is 514.
#
# [Unix flavours should use this format...]
# output alert_syslog: LOG_AUTH LOG_ALERT
#
# [Win32 can use any of these formats...]
# output alert_syslog: LOG_AUTH LOG_ALERT
# output alert_syslog: host=hostname, LOG_AUTH LOG_ALERT
# output alert_syslog: host=hostname:port, LOG_AUTH LOG_ALERT
# log_tcpdump: log packets in binary tcpdump format
# -------------------------------------------------
# The only argument is the output file name.
#
# output log_tcpdump: tcpdump.log
# database: log to a variety of databases
# ---------------------------------------
# See the README.database file for more information about configuring
# and using this plugin.
#
# output database: log, mysql, user=root password=test dbname=db
host=localhost
# output database: alert, postgresql, user=snort dbname=snort
# output database: log, odbc, user=snort dbname=snort
# output database: log, mssql, dbname=snort user=snort password=test
# output database: log, oracle, dbname=snort user=snort password=test
# unified: Snort unified binary format alerting and logging
# -------------------------------------------------------------
# The unified output plugin provides two new formats for logging and
generating
# alerts from Snort, the "unified" format.  The unified format is a
straight
# binary format for logging data out of Snort that is designed to be
fast and
# efficient.  Used with barnyard (the new alert/log processor), most of
the
# overhead for logging and alerting to various slow storage mechanisms
such as
# databases or the network can now be avoided.  
#
# Check out the spo_unified.h file for the data formats.
#
# Two arguments are supported.
#    filename - base filename to write to (current time_t is appended)
#    limit    - maximum size of spool file in MB (default: 128)
#
# output alert_unified: filename snort.alert, limit 128
# output log_unified: filename snort.log, limit 128
# You can optionally define new rule types and associate one or more
output
# plugins specifically to that type.
#
# This example will create a type that will log to just tcpdump.
# ruletype suspicious
# {
#   type log
#   output log_tcpdump: suspicious.log
# }
#
# EXAMPLE RULE FOR SUSPICIOUS RULETYPE:
# suspicious tcp $HOME_NET any -> $HOME_NET 6667 (msg:"Internal IRC
Server";)
#
# This example will create a rule type that will log to syslog and a
mysql
# database:
# ruletype redalert
# {
#   type alert
#   output alert_syslog: LOG_AUTH LOG_ALERT
#   output database: log, mysql, user=snort dbname=snort host=localhost
# }
#
# EXAMPLE RULE FOR REDALERT RULETYPE:
# redalert tcp $HOME_NET any -> $EXTERNAL_NET 31337 \
#   (msg:"Someone is being LEET"; flags:A+;)
#
# Include classification & priority settings
# Note for Windows users:  You are advised to make this an absolute
path,
# such as:  c:\snort\etc\classification.config
#
include classification.config
#
# Include reference systems
# Note for Windows users:  You are advised to make this an absolute
path,
# such as:  c:\snort\etc\reference.config
#
include reference.config
####################################################################
# Step #4: Customize your rule set
#
# Up to date snort rules are available at http://www.snort.org
#
# The snort web site has documentation about how to write your own
custom snort
# rules.
#
# The rules included with this distribution generate alerts based on on
# suspicious activity. Depending on your network environment, your
security
# policies, and what you consider to be suspicious, some of these rules
may
# either generate false positives ore may be detecting activity you
consider to
# be acceptable; therefore, you are encouraged to comment out rules that
are
# not applicable in your environment.
#
# The following individuals contributed many of rules in this
distribution.
#
# Credits:
#   Ron Gula <rgula () securitywizards com> of Network Security Wizards
#   Max Vision <vision () whitehats com>
#   Martin Markgraf <martin () mail du gtn com>
#   Fyodor Yarochkin <fygrave () tigerteam net>
#   Nick Rogness <nick () rapidnet com>
#   Jim Forster <jforster () rapidnet com>
#   Scott McIntyre <scott () whoi edu>
#   Tom Vandepoel <Tom.Vandepoel () ubizen com>
#   Brian Caswell <bmc () snort org>
#   Zeno <admin () cgisecurity com>
#   Ryan Russell <ryan () securityfocus com>
 
#=========================================
# Include all relevant rulesets here 
# 
# The following rulesets are disabled by default:
#
#   web-attacks, backdoor, shellcode, policy, porn, info, icmp-info,
virus,
#   chat, multimedia, and p2p
#            
# These rules are either site policy specific or require tuning in order
to not
# generate false positive alerts in most enviornments.
# 
# Please read the specific include file for more information and
# README.alert_order for how rule ordering affects how alerts are
triggered.
#=========================================
include $RULE_PATH/local.rules
include $RULE_PATH/bad-traffic.rules
include $RULE_PATH/exploit.rules
include $RULE_PATH/scan.rules
include $RULE_PATH/finger.rules
include $RULE_PATH/ftp.rules
include $RULE_PATH/telnet.rules
include $RULE_PATH/rpc.rules
include $RULE_PATH/rservices.rules
include $RULE_PATH/dos.rules
include $RULE_PATH/ddos.rules
include $RULE_PATH/dns.rules
include $RULE_PATH/tftp.rules
include $RULE_PATH/web-cgi.rules
include $RULE_PATH/web-coldfusion.rules
include $RULE_PATH/web-iis.rules
include $RULE_PATH/web-frontpage.rules
include $RULE_PATH/web-misc.rules
include $RULE_PATH/web-client.rules
include $RULE_PATH/web-php.rules
include $RULE_PATH/sql.rules
include $RULE_PATH/x11.rules
include $RULE_PATH/icmp.rules
include $RULE_PATH/netbios.rules
include $RULE_PATH/misc.rules
include $RULE_PATH/attack-responses.rules
include $RULE_PATH/oracle.rules
include $RULE_PATH/mysql.rules
include $RULE_PATH/snmp.rules
include $RULE_PATH/smtp.rules
include $RULE_PATH/imap.rules
include $RULE_PATH/pop2.rules
include $RULE_PATH/pop3.rules
include $RULE_PATH/nntp.rules
include $RULE_PATH/other-ids.rules
# include $RULE_PATH/web-attacks.rules
# include $RULE_PATH/backdoor.rules
# include $RULE_PATH/shellcode.rules
# include $RULE_PATH/policy.rules
# include $RULE_PATH/porn.rules
# include $RULE_PATH/info.rules
# include $RULE_PATH/icmp-info.rules
 include $RULE_PATH/virus.rules
# include $RULE_PATH/chat.rules
# include $RULE_PATH/multimedia.rules
# include $RULE_PATH/p2p.rules
include $RULE_PATH/experimental.rules
# Include any thresholding or suppression commands. See threshold.conf
in the
# <snort src>/etc directory for details. Commands don't necessarily need
to be
# contained in this conf, but a separate conf makes it easier to
maintain them. 
# Note for Windows users:  You are advised to make this an absolute
path,
# such as:  c:\snort\etc\threshold.conf
# Uncomment if needed.
# include threshold.conf
I really do appreciate your response. Thanks a bunch.

"Matthew K. Lee" <mattl () rycan com> wrote:
        Jeremiah,
        
        I think you may be missing your Unicode.map file. Try to place
that
        file where it needs to be. If that doesn't work, you might try
to
        comment out the http_inspect lines to see if you have a
configuration
        problem there. If that still doesn't work, you may want to post
your
        snort.conf file to the list.
        
        Thanks,
        
        Matt
        
        -----Original Message-----
        From: Jeremiah J Batac [mailto:jjbatac () yahoo com] 
        Sent: Friday, November 12, 2004 6:28 AM
        To: snort-users () lists sourceforge net
        Subject: [Snort-users] HELP!!! HELP!!! HELP!!!
        
        hello snort users,,, im a newbie in the IDS field. Im
        trying my best to make this snort thing to work in
        Windows XP. I'm so frustrated coz after downloading
        tons of documents to help me set it up, tried all
        their steps and guess what its partially working...
        Can somebody kind enough to walk me through to make it
        work. current softwares to install snort that i have
        right now are the following...
        
        acid
        adodb
        dbtools
        libnet-1.0.2f
        packetbuild-1.4
        php-4.3.9-win32
        phplot-4.4.6
        application_service
        mysqlsetup
        snort-2_1_0
        winpcap_3_0
        
        
        I already tried to install and follow the steps 5times
        and unfortunately i just go up to this point
        
        
        C:\Snort>snort
        Running in IDS mode with inferred config file:
        ./snort.conf
        Log directory = log
        
        Initializing Network Interface
        \Device\NPF_{3A842A08-FAFC-4986-A869-4AB8B6C9DD67
        }
        
        --== Initializing Snort ==--
        Initializing Output Plugins!
        Decoding Ethernet on interface
        \Device\NPF_{3A842A08-FAFC-4986-A869-4AB8B6C9DD67
        }
        Initializing Preprocessors!
        Initializing Plug-ins!
        Parsing Rules file ./snort.conf
        
        +++++++++++++++++++++++++++++++++++++++++++++++++++
        Initializing rule chains...
        ,-----------[Flow Config]----------------------
        | Stats Interval: 0
        | Hash Method: 2
        | Memcap: 10485760
        | Rows : 4099
        | Overhead Bytes: 16400(%0.16)
        `----------------------------------------------
        No arguments to frag2 directive, setting defaults to:
        Fragment timeout: 60 seconds
        Fragment memory cap: 4194304 bytes
        Fragment min_ttl: 0
        Fragment ttl_limit: 5
        Fragment Problems: 0
        Self preservation threshold: 500
        Self preservation period: 90
        Suspend threshold: 1000
        Suspend period: 30
        Stream4 config:
        Stateful inspection: ACTIVE
        Session statistics: INACTIVE
        Session timeout: 30 seconds
        Session memory cap: 8388608 bytes
        State alerts: INACTIVE
        Evasion alerts: INACTIVE
        Scan alerts: INACTIVE
        Log Flushed Streams: INACTIVE
        MinTTL: 1
        TTL Limit: 5
        Async Link: 0
        State Protection: 0
        Self preservation threshold: 50
        Self preservation period: 90
        Suspend threshold: 200
        Suspend period: 30
        Stream4_reassemble config:
        Server reassembly: INACTIVE
        Client reassembly: ACTIVE
        Reassembler alerts: ACTIVE
        Zero out flushed packets: INACTIVE
        flush_data_diff_size: 500
        Ports: 21 23 25 53 80 110 111 143 513 1433
        Emergency Ports: 21 23 25 53 80 110 111 143 513
        1433
        ERROR: ./snort.conf(287) => Invalid file name for IIS
        Unicode Map file.
        Fatal Error, Quitting..
        
        C:\Snort>
        
        hope this will help. like you i would like to be a
        pioneer on this OpenSource IDS. Help is much
        appreciated. Thank you very much.
        
        
        
        
        
        __________________________________ 
        Do you Yahoo!? 
        Check out the new Yahoo! Front Page. 
        www.yahoo.com 
        
        
        
        
        -------------------------------------------------------
        This SF.Net email is sponsored by:
        Sybase ASE Linux Express Edition - download now for FREE
        LinuxWorld Reader's Choice Award Winner for best database on
Linux.
        http://ads.osdn.com/?ad_id=5588&alloc_id=12065&op=click
        _______________________________________________
        Snort-users mailing list
        Snort-users () lists sourceforge net
        Go to this URL to change user options or unsubscribe:
        https://lists.sourceforge.net/lists/listinfo/snort-users
        Snort-users list archive:
        http://www.geocrawler.com/redir-sf.php3?list=snort-users
  _____  

Do you Yahoo!?
Check out the new Yahoo! Front Page. www.yahoo.com