nanog mailing list archives

Re: Juniper BGP Convergence Time


From: Adam Kajtar <akajtar () wadsworthcity org>
Date: Wed, 16 May 2018 13:43:24 -0400

I did exactly that when I called. One is looking into the other hasn't
called yet. I will let you know what they say.

On Wed, May 16, 2018 at 12:59 PM Phil Lavin <phil.lavin () cloudcall com>
wrote:

Ask if they will configure BFD for you. I’ve not found many transit
providers that will, but it’s worth a shot and it will lower failure
detection to circa 1 second.


On 16 May 2018, at 17:49, Adam Kajtar <akajtar () wadsworthcity org> wrote:

I could use static routes but I noticed since I moved to full routes I
have
had a lot fewer customer complaints about latency(especially when it
comes
to Voice and VPN traffic).

I wasn't using per-packet load balancing. I believe juniper default is
per
IP.

My timers are as follows
Active Holdtime: 90
Keepalive Interval: 30

Would I be correct in thinking I need to contact my ISP to lower these
values?

An interesting note is when I had both ISPs connected into a single MX104
the failover was just a few seconds.

Thanks again.



On Tue, May 15, 2018 at 8:42 PM Ben Cannon <ben () 6by7 net> wrote:

Have you checked your timeouts ?

-Ben

On May 15, 2018, at 4:09 PM, Kaiser, Erich <erich () gotfusion net>
wrote:

Do you need full routes?  What about just a default route from BGP?

Erich Kaiser
The Fusion Network
erich () gotfusion net
Office: 815-570-3101




On Tue, May 15, 2018 at 5:38 PM, Aaron Gould <aaron1 () gvtc com> wrote:

You sure it doesn't have something to do with 60 seconds * 3 = 180
secs
of
BGP neighbor Time out before it believes neighbor is dead and remove
routes
to that neighbor?

Aaron

On May 15, 2018, at 9:10 AM, Adam Kajtar <akajtar () wadsworthcity org>
wrote:

Hello:

I'm running two Juniper MX104s. Each MX has 1 ISP connected running
BGP(full routes). iBGP is running between the routers via a two port
20G
lag. When one of the ISPs fails, it can take upwards of 2 minutes for
traffic to start flowing correctly. The router has the correct route
in
the
routing table, but it doesn't install it in the forwarding table for
the
full two mins.

I have a few questions if anyone could answer them.

- What would a usual convergence time be for this setup?
- Is there anything I could do speed this process up? (I tried
Multipath)
- Any tips and tricks would be much appreciated

Thanks in Advance
--
Adam Kajtar
Systems Administrator
City of Wadsworth
akajtar () wadsworthcity org
-----------------------------------------------------
http://www.wadsworthcity.com

Facebook <http://www.facebook.com/cityofwadsworth>* |* Twitter
<https://twitter.com/CityOfWadsworth> *|* Instagram
<https://www.instagram.com/cityofwadsworth/> *|* YouTube
<https://www.youtube.com/channel/UCymlH-AZgvxTaHtgp3-AmDQ>





--
Adam Kajtar
Systems Administrator, Safety Services
City of Wadsworth
Office 330.335.2865
Cell 330.485.6510
akajtar () wadsworthcity org
-----------------------------------------------------
http://www.wadsworthcity.com

Facebook <http://www.facebook.com/cityofwadsworth>* |* Twitter
<https://twitter.com/CityOfWadsworth> *|* Instagram
<https://www.instagram.com/cityofwadsworth/> *|* YouTube
<https://www.youtube.com/channel/UCymlH-AZgvxTaHtgp3-AmDQ>



-- 
Adam Kajtar
Systems Administrator, Safety Services
City of Wadsworth
Office 330.335.2865
Cell 330.485.6510
akajtar () wadsworthcity org
-----------------------------------------------------
http://www.wadsworthcity.com

Facebook <http://www.facebook.com/cityofwadsworth>* |* Twitter
<https://twitter.com/CityOfWadsworth> *|* Instagram
<https://www.instagram.com/cityofwadsworth/> *|* YouTube
<https://www.youtube.com/channel/UCymlH-AZgvxTaHtgp3-AmDQ>


Current thread: